Pilgrim73
TATbRHA
But I just didn’t find what to do if the stirrer cannot be removed ... Tell me, who knows.

Pour into a bucket of warm water and let stand for 10-15 minutes. Everything will get wet and the stirrer can be easily removed.
Lagri
I have an LG HB-1002CJ bread maker. After the first baking of bread in the Basic program, the display shows [H]. What does it mean? I just turned off the stove.
TATbRHA
This means that the given program has ended, then the three-hour keeping of the bread warm will go. But he doesn't like bread very much, but loves when it is put to cool on the wire rack. Turned off - and did the right thing :).
Lagri
Quote: inga48

found damage to the coating inside the bucket. On the wall it swelled and burst, and at the bottom at the very screw it turned white and was about to peel off too. Operated clearly according to the instructions, and now I did not have time to enjoy the purchase on you either.
Quote: inga48

Will they replace my bucket? After all, the guarantee is not over yet.
Quote: alexs48

Obliged, the bucket is quite expensive.
I had a similar one and did not change, although the warranty did not end. They said in the Service that the device is working properly, bakes normally (they made a control baking), but they did not want to listen to the coating of the bucket (the coating was covered with the beginning on the ledges inside the bucket). I had to buy a new one for my own money. But that was with Moulinex. Maybe LG is "more responsive" to customers and will change ...
Vitaok
Hello everyone! Please tell me who knows! : this: I have been using HP LG HB-3001byt for a month and I can't get a "night" bread. If I bake during the day, the bread is excellent. And the one that I put on the timer for the morning turns out to be heavy, large-pored, the tip is sunken
Azimut
The Teflon coating does not like it if cold water is immediately poured into the hot bucket after baking. Because of this, the non-stick coating may peel off, so let the bucket cool down.
Azimut
Quote: vitaokstep

Hello everyone! Please tell me who knows! : this: I have been using HP LG HB-3001byt for a month and I can't get a "night" bread. If I bake during the day, the bread is excellent. And the one that I put on the timer for the morning turns out to be heavy, large-pored, the tip is sunken

Perhaps during the delay, the yeast gets wet and starts working earlier than necessary. It is recommended to put the yeast at the very top.

Check the delay from morning to evening and look at the yeast just before kneading.
koiot
Hello! My LG HB-202CE sensor does not work on it (((((help pliz ((((P.S. disassembled, whole wires)
gulyaz
Hello. The LG HB-202CE oven broke down. I started the bread as usual, mixed it, the bun rose, baking began, after about five minutes the oven suddenly began to squeak chaotically, as if it was turned off and on, and something crackled under the buttons. You remove the plug from the socket, insert it, again the same thing. Programs are not included. The stove is 1.5 years old. What do you advise?
gulyaz
Disassembled, jerked several times all the plugs on the board, EARNED !!!) Looks like the contacts burned in 1.5 years. I baked two loaves - no problem! :-)
Coolly
Hello everyone!) I just registered) I am choosing a bread maker as a gift for my parents for the new year! attention focused on the HB 1002cj or 1001cj models. Please tell me who has such a model, who thinks what)
Valyushka-bun
Dear forum users. Please tell me what material you have knives in bread makers from? Today I bought a knife-kneader for the stove and later I saw that it was plastic, to be honest I don't really remember, but it seems to me that the previous knife was made of metal. I have an LG 151 JE.
kss
tell me, I have an LG 3001, in the fast mode I stopped baking, the bread rises well, but not baked at all, raw and white as dough, in general it seems that there is not enough temperature, I have to bake in the oven. In other modes, everything is fine. What could be the reason, who knows?
Vitaok
I only baked once on the "fast" mode and I had the following result: not baked, damp, and also the smell of yeast. Although the top color of the crust was usual - beautiful, golden. : pardon: I no longer use this mode.
Creamy
But it seems to me that everything is more banal and simpler - there is not enough time for baking on the fast setting.
Vitaok
I agree with you 100%, but kss she "stopped baking" ...
kss
Quite right, just stopped. We have been using it for about a year, there were no problems. It is a pity that there are no temperature conditions in those descriptions, I think the problem is in the temperature. I checked it with a food thermometer, the temperature in the loaf itself was less than 70 degrees. By the way, I noticed that in other modes, too, not everything is in order. With regard to baking bread, everything is fine, the bread is not soggy, not soggy, but when you set the color of the crust, for example, dark, the oven does not react and bakes medium. Above, they seemed to describe similar problems, the reason was, if I am not mistaken about the conductors, but I am far from electronics, I would be on my fingers so to speak.
mixail33
Good guys.
Stove HB202SE burned out. Rather, the fuse in the primary winding is blown out. trance is most likely from increased stress on the network. We have 270 volts in winter.
I soldered the fuse, checked it - all the way. Soldered back the trance to the board. But KhPechka does not give out any reaction. I checked the conductors, the diodes on the board rang - everything is intact ... Guys, who can give me an HB202 circuit with cords to dig in the right direction? Or maybe you can help ... Huh?
Khpechka is desperately needed - because bread is the head of everything ...
sazalexter
mixail33 Oh smiled

Quote: mixail33


Good guys.
Measure the pressure after the transformer, is there? If yes, the mikruha is dead. There is no scheme for this HP, everything is "by scientific poke method"
mixail33
Quote: sazalexter

mixail33 Oh smiled
Measure the pressure after the transformer, is there? If yes, the mikruha is dead. There is no scheme for this HP, everything is done by "scientific poke"

I turned to the men
There is a spill after a trance - 12c. The scheme is almost the same as in Repair and Service for No. 12 2006 (reference higher in the kamenty)
OU! If mikruha - then I pass !!!! Was it covered with a copper basin?

sazalexter
mixail33 To be sure, I would have waved all the electrolytes, if it does not help and I do not know what to do, was there some kind of infa about the control transistor? on the internet, I don't remember where
mixail33
Quote: sazalexter

mixail33 To be sure, I would have waved all the electrolytes, if it does not help and I do not know what to do, was there some kind of infa about the control transistor? on the internet, I don't remember where

Buddy, literally in half an hour I'll look at the board, check the mikruhi input, electrolytes and write right away.
mixail33
Quote: mixail33

Buddy, literally in half an hour I'll look at the board, check the mikruhi input, electrolytes and write right away.

In general, I dug - not a devil, the scheme does not fit ...
Electrolytes are called workers. Mikruha OIHI4043440 HD404344B03S I'll look in the internet, find out the pinout. An interesting moment - there are no tensions on any leg of mikruhi. Most likely something with nutrition. There is voltage after the diode bridge. There is no way to check further - I'm tired and the parts are small. I can't concentrate.
sazalexter
Electrolytes can really be checked only on the device, for leaks or by replacement. In terms of nutrition, there should be a KRENKA in theory.
sazalexter
mixail33 Take a photo of the board and put it here, let's see together
mixail33
Quote: sazalexter

mixail33 Take a photo of the board and put it here, let's see together
Now
mixail33
Quote: mixail33

Now
here you are

🔗
🔗
sazalexter
It looks like KRENK's Is2 and most likely at 5v, well, maybe at 7v. More precisely, if I see the marking.
mixail33
Quote: sazalexter

It looks like KRENK's Is2 and most likely at 5v, well, maybe at 7v. More precisely, if I see the marking.
So so so - is 2 Where is he? I just can't find it. Looks like a big transistor?
This?
🔗
mixail33
Ah ... found everything. Now I'll take a picture of it and put up the markings
sazalexter
Small as a transistor near a large blue connector and I'm still interested in the element transistor or triac between two electrolytes, large and small, very similar to the TO220 case The one that highlighted in red
mixail33
Quote: mixail33

Ah ... found everything. Now I'll take a picture of it and put up the markings
🔗

and here is the trans that I circled in red:

🔗
sazalexter
Hmm I was wrong this is BIPOLAR LINEAR INTEGRATED CIRCUIT (VOLTAGE DETECTOR) 🔗 need to think...
sazalexter
And Red KREN 5B urraaa! Check it, better change it
mixail33
Quote: sazalexter

And Red KREN 5B urraaa! Check it, better change it

Buddy, what can you replace with something? Well, there is nothing at hand ...
And I don't know how to check ... be a friend, explain pliz step by step
sazalexter
At the entrance from the left to the right on the board is signed "I", approximately 7-10 V, the middle is ground, at the exit, the right leg is 5 volts.
mixail33
Quote: sazalexter

At the entrance from the left to the right on the board is signed "I", approximately 7-10 V, the middle is ground, at the exit, the right leg is 5 volts.

I'm going to die now.
sazalexter
You can replace it with KREN-5 or 7805 of almost any manufacturer
mixail33
at the input of the CRENA 0.22 volts, and at the output - 0 volts. What does that mean?
mixail33
Quote: sazalexter

You can replace it with KREN-5 or 7805 of almost any manufacturer

Buddy, help a ...
sazalexter
Check D5 and R101
mixail33
Quote: sazalexter

Check D5 and R101

I'm just poking around there
mixail33
sazalexter, A huge human THANKS to you !!!!!!!
Everything worked out! It took time to select the parameter of the resistor R101, since I do not understand the color coding. It was necessary to put 200 ohms. We will eat the first bread for your health! Thank you

sazalexter
mixail33 Congratulations on a successful renovation
oyster mushroom
Good day everyone! I shoveled up and down the forum, but I never found anyone to change the bucket from lg hb-152 ce. The inner coating was damaged. Apparently we are the only such-boobies. In the internet I found a "buy" bucket, but 2 tons. R. It's a pity (and even more for the transfer!) Maybe someone would. ear will tell you where to buy? Although ... all of a sudden, with such "rattling" it will get ... We did not have ANY problems at all. Sorry for the stove. She has already been with us for 5-6 years.
I write myself and come to the conclusion that I will have to buy a new HP.
Or maybe there are still options? A?
Creamy
Well, you will buy expensive shoes for an ancient old woman, but what if soon the old woman herself orders to live long? It is more profitable to buy a new bread maker, there is a new engine and seals and a bucket and another guarantee. We must woo the young.
mixail33
Quote: oyster mushroom

Good day everyone! I shoveled up and down the forum, but I never found anyone to change the bucket from lg hb-152 ce. The inner coating was damaged. Apparently we are the only such-boobies. In the internet I found a "buy" bucket, but 2 tons. R. It's a pity (and even more for the transfer!) Maybe someone would. ear will tell you where to buy? Although ... all of a sudden, with such "rattling" it will get ... We did not have ANY problems at all. Sorry for the stove. She has already been with us for 5-6 years.
I write myself and come to the conclusion that I will have to buy a new HP.
Or maybe there are still options? A?

How is the damage to the coating on the bread making process expressed? Does the bread stick? Or what? I know that in industrial bakeries, bread is fried in simple aluminum molds, without any coating - before baking, the molds are simply smeared with sunflower oil from the inside.
Although in bakeries, ready-made dough lies in the mold.

mixail33
Quote: Creamy

Well, you will buy expensive shoes for an ancient old woman, but what if soon the old woman herself orders to live long? It is more profitable to buy a new bread maker, there is a new engine and seals and a bucket and another guarantee. We must woo the young.

Man is sorry for 2 pieces, but you say a new one ... Although in principle you are right.
mixail33
Here, 1200 rubles - all the pleasure is worth. Call, chat, agree ...
🔗
Taia
On Ukrainian sites, a new bucket for LG costs $ 25. I would take a chance, normal price.

All recipes

© Mcooker: best recipes.

map of site

We advise you to read:

Selection and operation of bread makers